BETA IS EQUIPPED WITH ONE MAGAZINE:

HIGH SINGLE LEVEL, has a single loading plane of 235mm positioned at guide channel height that is manually adjusted to the process bar diameter via micro metric screw. To guarantee operator safety, the high single level is protected by the front loader door which, when opened by means of a safety hinge, inhibits dangerous movements.

AUTOMATIC MANAGEMENT

The BETA loader is managed by a PLC, which interacts with a Brushless motor and with digital solenoid valves, to regulate the feed speed, the thrust force and all the automations. In fact, it is possible to reprogram the diameter to be processed in just 60 seconds from the PLC.

BETA AS LOADER-LATHE INTERFACE IS EQUIPPED WITH:

STANDARD TUBE: direct interface between loader and lathe, covered in polyurethane material of the maximum passage of the loader bar;

GUIDE CHANNEL

BETA has a manually interchangeable round section channel; thanks to its Vulkollan plastic material, it is extremely resistant to the oil bath and to the high rotation speed of the bar.

FRONT BUSHING

BETA has an interchangeable bushing every 5mm at the front of the loader: thanks to this device, it is possible to achieve high bar rotation performance.

SEGMENT MANAGEMENT

BETA has two types of segment management: 1) Back extraction performed by means of a self-centring extractor, which allows the piece inside the magazine to be extracted and expelled into the special recovery tank.
 This type of extraction does not require any adjustment and setting as the extractor is self-centring. 2) Front ejection performed by ejecting the segment from the front of the lathe clamp, pushing the segment to be unloaded with the load of the new bar in the lathe clamp. It is used to work bars of maximum diameter with respect to the lathe spindle turn buckle as there would be no space to grasp the bar with the elastic clamp on the outside of the diameter.

LANCE SYSTEM

BETA has a retractable lance that allows you to maintain reduced measurements on the total length of the loader by hooking it to the cover during bar change. The lance has a front rotor where the elastic bar clamp is mounted and allows rotation at the same rpm of the lathe spindle. It includes rotating brass bushings along the length that do not seize inside the spindle.

ELECTRIC PANEL / INTERFACE

BETA includes an electrical system entirely designed and assembled in Top Automazioni with high quality brands such as: Phoenix, Eaton, Esa, Siboni. TOP AUTOMAZIONI includes any interface required by the lathe on its loaders wired to the specifications of the lathe manufacturers such as: 24-pole interface, profibus interface, ethercat interface, modular multipolar interface.

SEGMENT UNLOADING

BETA has a segment unloader on the back of the magazine where they are collected in a 200x200x850 tank.

OIL PUMP AND FILTER

For guide channel lubrication, BETA includes a gear pump with a capacity of 7.5 litres connected to a 90 micron filter that cleans the oil before putting it into circulation in the hydraulic system. The filter is easily reachable to perform periodic cleaning, which is indicated by a vacuum gauge indicator.

BETA is an automatic loader suitable for fixed head lathes, can process bars up to 50mm in diameter and is available in different length versions from 2000-3000-4000 mm.

BETA has an oil-bath polyurethane guide channel with circular cross-section according to the lathe bar passage. A self-centring bushing is found at loader outfeed that must be replaced every 5mm based on the diameter of the bar being processed.

BETA is a robust and very stable loader, available in the high single-level magazine version.

Bar diameter range
Min. Ø 6mm - Max. Ø 50mm Min. Ø 0,23" - Max. Ø 1,96"
Operating voltage
230 V Trifase 50 Hz Three Phase
Feeding speed
0 - 627 mm/sec. 0 - 24,70"/sec.
Guide channel lubricant
ISO VG 68
Required air pressure
8 bar
Weight
1.800 Kg 3.968 lb
Maximum bar lenght
3200mm - 4100mm 10.50 ft – 13.45 ft

Download

Download Technical Data